Eagle Mach 1 Especificaciones descargar pdf (Pagina 14)

15” ASTRO-PHYSICS DOVETAIL (DOVE15) FOR 15” SLIDING BAR (SB1500)

The 15" version of our dovetail plate is suited for the 130 f8 StarFire

EDT, 155 f7 StarFire EDFS, Takahashi scopes and other instruments of

similar size. The two knob assemblies each feature a brass pin with a

tapered end to hold your sliding bar firmly without marring the aluminum.

Use with the 15" Sliding Bar (SB1500), which is sold separately (NOT for

use with Losmandy “D” plates). Also makes a great accessory plate

when used with either the 900RP, the FP1500, the FP1800 (with rings

mounted to inside holes) or another DOVE15.

Attach with four 1/4-20 x 1/2” flat head socket cap screws.

8.5” DOVETAIL FOR LOSMANDY D SERIES PLATE (DOVELM2)

This Astro-Physics plate attaches to the 400, 600E, 900, 1200 and Mach1GTO mounts. If

you already own one of the Losmandy DAP series (fits Astro-Physics refractors), DC series

(for Celestron 8" 9.25” or 11" SCTs) or DM series (for Meade 8" and 10" SCTs) plates, y

should consider this plate or the longer DOVELM16S or DOVELM162. For larger size SCTs

we recommend the Easy-Balance DOVELM162 – see below.

-20 x 5/8" socket head cap screws.

Note that the two larger bolt-hole patterns are offset from the center. This allows you to

position the plate either forward or backward depending on the balance point of your

telescope. Attach this plate with four 1/4

16" EASY-BALANCE DOVETAIL FOR MACH1GTO, 900 AND 1200 MOUNTS AND LOSMANDY D SERIES PLATES

(DOVELM162)

This Astro-Physics plate was introduced in February, 2009. The

DOVELM162 provides a multitude of mount attachment options, and

was specifically designed to meet the balancing demands of “back-

end-heavy” instruments like SCTs and Richey-Chrétiens, especially

those with heavy imaging gear hanging off the back! This plate has

small knobs to avoid interference with the declination hub, but the

knobs have cap screws in the ends that accept a 3/16 hex wrench

for extremely secure clamping of your instrument. Additional

features include ribbed structure underneath to reduce weight and

tapped 10-32 holes in the side for cable attachment.

Note that the bolt-hole patterns are marked with scribe cuts. Attach this plate with four 1/4-20 x 1" socket head cap screws.

16" DOVETAIL FOR LOSMANDY D SERIES PLATES (DOVELM16S)

This Astro-Physics plate attaches to the 900 and Mach1GTO

mounts. If you already own one of the longer Losmandy DAP series

(fits larger Astro-Physics refractors), DC series (for Celestron 8" or

9.25" SCTs) or DM series (for Meade 8", and 10" SCTs) plates, this

is the mounting plate for you.

Note that the bolt-hole pattern is offset from the center. This allows

you to position the plate either slightly forward or backward

depending on the balance point of your telescope. Attach this plate with four 1/4-20 x 7/8" socket head cap screws. NOTE:

As of this writing, this plate will be available as long as quantities last. It is being

phased out in favor of the DOVELM162 (above).

NOTES ON ATTACHING THE ABOVE MOUNTING PLATES:

Three of the components listed above have six mounting holes that match the six

screw holes that hold the D

ECLINATION HUB PLATE onto the hub of the Mach1GTO’s

Dec axis. (FP1800, 900RP and Q4047) We recommend that you use only four of

these holes to mount your plate. Remove four of the screws that hold the

ECLINATION HUB PLATE in place. They will be replaced by the four screws that hold

the mounting plate down. The remaining two can then still hold the D

ECLINATION HUB

PLATE in place on the DECLINATION AXIS HUB while the mounting plate is being

attached. The four remaining holes are more than adequate to hold the plate

securely on the mount. It really doesn’t matter which four you choose, but the two

screws left to hold the D

ECLINATION HUB PLATE in place should probably be opposite

each other. You may also remove the D

ECLINATION HUB PLATE if you wish.

You will also notice that in addition to the four holes that make up the inside pattern

on the D

ECLINATION HUB PLATE, there is an extra hole that matches an extra hole

found in two of the Losmandy style plates (DOVELM2 and DOVELM16S). This fifth

hole is not used if the four regular holes are in use. However, if you lose a

mounting screw, it can be used in place of the two normal holes on that end of the

plate to make a very solid 3 point attachment.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 32 33

Comentarios a estos manuales

Sin comentarios

Eagle Mach 1 Especificaciones Pagina 14

Comentarios a estos manuales